Pro master Timer Remote Uživatelský manuál stáhnout pdf (Strana 1)

T-MAX

Parameter Setting Guide

for single 3-A timers and 3-A remote timer systems.

Getting into the parameters

1. Remove timer from any other timers (if any).

2. Cycle power to timer.

3. When the timer displays * 0*, press and hold the START/STOP and UP arrow at the same

time until the display reads * .1* (Solid decimal, solid one.) Release the buttons.

4. After making any changes to any parameters, press and hold the UP and DOWN arrows at

the same time to exit.

Note: To exit, there must not be ANY numbers flashing. If there are, press START/STOP to

exit that parameter, then try again.

Setting bed address

1. Get into parameters mode. (see above)

2. Go to parameter * .1* (solid decimal, solid one). When you get into the parameters mode,

you should start off at parameter * .1*.

3. Press the START/STOP button once. The numbers should be flashing. This is your bed

address.

4. Use UP and DOWN arrows to change bed address.

a. Solid decimal and 0~99 = 0~99

b. Flashing decimal and 0~28 = 100~128

c. Flashing decimal and 52~55 are not bed addresses.

d. Setting the bed address to zero * .0* (solid decimal flashing zero) will make that timer a

remote timer.

5. Once you have your bed address set, press the START/STOP button once. The display

should then read * .1* (solid decimal, solid one).

6. Exit, unless you are making changes to other parameters.

Setting the session delay

1. Get into parameters mode. (see above)

2. Press the UP arrow to take you to parameter * .3* (solid decimal, solid three)

3. Press the START/STOP button once.

4. Use the UP and DOWN arrows to set the amount of time, in minutes, that you want to give

the person. This is the amount of time they have to get ready before the bed starts.

a. Time can be set between 0~10 minutes.

5. Press the START/STOP button once, to set that parameter.

6. Exit, unless you are making changes to other parameters.

Enable/ Disable the Clean Room Feature

1. Get into parameters mode.

2. Use the UP arrow to get to parameter * .9* (solid decimal, solid nine)

3. Press the START/STOP button once. A number will start flashing.

4. Set the parameter to

a. 0= Clean Room off.

b. 1= Clean Room on.

1 2 3 4 5

Parameter Setting Guide 1

Shrnutí obsahu

Strany 1 - Parameter Setting Guide

T-MAX Parameter Setting Guide for single 3-A timers and 3-A remote timer systems. Getting into the parameters 1. Remove timer from any other time

Strany 2

5. Press the START/STOP button once. 6. Exit. Unless you are making changes to other parameters. Troubleshooting A remote 3-A timer with a 3-A T-

Strany 3

b. Enter a 0 if you want the person to have to press the start button in order for the bed to turn on after the session delay. If the session delay

Strany 4

TROUBLESHOOTING Can’t Send Time To Bed 1. Make sure you have entered a pass code that is at least a level 1 or higher. There should be at least one

Strany 5

1. Make sure the timer is not connected to any other timer or a T-MAX Manager Plus/PRO. 2. Remove power from the timer. 3. With the power removed,

Další dokumenty pro Příslušenství k fotoaparátu Pro master Timer Remote

Zobrazit dokument Pro master Timer Remote Uživatelský manuál

Pro master Timer Remote Uživatelský manuál (40 stránky)

Pro master Timer Remote Uživatelský manuál (2 stránky)

Zobrazit dokument Pro master Timer Remote Uživatelská příručka

Pro master Timer Remote Uživatelská příručka (16 stránky)

Komentáře k této Příručce

Žádné komentáře

Pro master Timer Remote Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Příslušenství k fotoaparátu Pro master Timer Remote. Timer Trouble Shoot PDF Uživatelská příručka

Shrnutí obsahu

Další dokumenty pro Příslušenství k fotoaparátu Pro master Timer Remote

Komentáře k této Příručce